Lijadora de espesor de tambor MicroLux®

$399.95 USD Agotado
Los gastos de envío se calculan en la pantalla de pago.

SKU

83507


La lijadora de espesor de tambor convierte su taller en un aserradero portátil


  • Lija madera de hasta ½ pulgada de espesor y 5 pulgadas de ancho
  • 1/3 hp con velocidad de tambor a 5800 rpm con potencia y precisión
  • Funciona con láminas o listones de madera.
  • Una exclusiva de MicroMark
  • Reduce la madera dura hasta 1/64 de pulgada.



ADVERTENCIA: Este producto puede exponerlo a productos químicos, incluido el polvo de madera, que el estado de California reconoce como causante de cáncer. Para obtener más información, visite: www.p65warnings.ca.gov
Más detalles del producto

Sands wood up to 1/2 inch thick and 5 inches wide



The MicroLux® Drum Thickness Sander is designed for model makers and serious hobbyists who need wood in sizes not available commercially. The rotating drum inside the housing sands wood sheet and strip to the desired size with a precision that will satisfy the most-demanding model builder. And the crafter can even manufacture his own lumber from resawn boards, or from wood sawn from small logs and other stock.



I needed about ten sheets of scribed sheetwood reduced from 1/16 to 1/32 thick. The drum thickness sander was a trooper and buzzed through them in a few minutes. I used a micrometer and the variation between boards and along each board was less than 0.003 inch. Looking around my shop, I said, 'There isn't another tool here that could do that. Bravo!'

Wayne W., Tucson, AZ

 -->

Use our web site shopping cart to calculate freight charge for shipments outside 48 contiguous U.S., or call our order line for assistance.

 









Specifications:









Drum size: 2 inches in diameter x 5-1/2 inches long



Capacity: Sands wood up to 1/2 inch thick and 5 inches wide



Motor: 1/3 horsepower, 120v AC



Drum speed: 5800 rpm



Sanding sleeves: Various grits available (sold separately)



Machine construction: Cast iron and steel plate



Drive system: Multi-V-belt



Accuracy: Table is adjustable side-to-side for uniform thickness



Vacuum port: Located on rear...1-1/4 inches in diameter



Overall size: 9 inches wide x 10 inches deep x 11 inches high



Weight: 33 lbs.



Includes one 120 grit sanding sleeve







Instrucciones
Envío y devoluciones

Esperamos que esté completamente satisfecho con su pedido... pero, si un artículo no cumple con sus expectativas, puede devolverlo como nuevo dentro de los 30 días posteriores a la entrega para un reemplazo, cambio o reembolso del precio de compra.

Estimación de envío

Contenido con pestañas


Marca: SHANGHAI INTER-SIEG CO

Agregue una breve descripción para esta sección con pestañas

Agregue una breve descripción para esta sección con pestañas

Customer Reviews

Based on 2 reviews
100%
(2)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
G
Gregory P.
Drum Sander surprise Provides nice finish.

This machine weighs in at 34#. I work mostly in mahogany wood and I cut my own veneer on a large bandsaw. I needed to remove all the teeth marks on the cut material. This unassuming little guy "egger beaver" did a great job. The material I cut is in different widths to fit my needs. I build Dumas mahogany type boats currently a Dauntless boat. This machine will fit my needs. It does not seem to slow down during the sanding process it does however create a whole lot of dust. which is a good thing, the finish is out standing. SO if you are doing veneer work this is the machine for you. The motor was turning the wrong way I called Micromark service tech he was on the mark for the repair over the phone... repair... Painless.

J
JACK E.
Great addition to model shop

The sander is very well preserved for storage and shipping. You will have to disassemble and thoroughly clean the machine.
The steel roller was already installed and had scored the table. Micro-Mark Customer Service immediately sent me a replacement table. They stand behind their products and have wonderful service.
When reassembling the sander, make sure to realign the table with the sanding drum as explained in the Maintenance section of the instructions.
I applied a thin coat of paste wax to the table to provide a smooth surface for the wood to slide on.
Even though the sander does not auto-feed the wood, it only took me two passes to get the feel for the correct speed to feed the wood.
I am very surprised at the overall hearty construction and ease of operation. This is a great addition to my model shop.

Recently Viewed
My Wishlist